Technical Document for Batch Waste Incineration
Information identified as archived on the Web is for reference, research or recordkeeping purposes. It has not been altered or updated after the date of archiving. Web pages that are archived on the Web are not subject to the Government of Canada Web Standards. As per the , you can request alternate formats on the page.Technical Document for Batch Waste Incineration Overview of the Six Step Process for Batch Waste IncinerationStep 1: Understand Your Waste StreamStep 2: Select the Appropriate Incinerator (or Evaluate the Existing System)Step 3: Properly Equip and Install the IncineratorStep 4: Operate the Incinerator for Optimum CombustionStep 5: Safely Handle and Dispose of Incinerator ResiduesStep 6: Maintain Records and ReportStep 1: Understand Your Waste StreamThe first step in managing waste is to understand the quantity and composition of the waste that is generated. Owners should investigate waste generation and diversion data from similar operations/facilities in order to estimate the waste types and quantities that will be generated at their own facilities.Based on the results of the waste audit/characterization, an assessment of appropriate disposal options should be undertaken. post 3Rs Reduce, Reuse, Recycle) should be examined. When assessing disposal options, it is important to note that waste should neither be open burned nor burned in a barrel. In both cases, the appropriate temperatures for a clean burn will not be achieved, and toxic contaminants, in particular dioxins and furans, will be released.Top of PageStep 2: Select the Appropriate Incinerator (or Evaluate the Existing System)The characteristics of the residual waste stream destined for incineration should be incorporated into a call for proposals from incinerator manufacturers. Specifying the quantity and composition of the waste stream will ensure that proposals include suitable incinerators. It should be noted that incinerators built for a specific waste stream, such as animal carcasses, liquid wastes and hazardous wastes , are available and should be used as required.For facilities with existing incinerators, owners/operators should reassess the suitability of the existing system to manage the current waste stream.For facilities incinerating more than 26 tonnes of waste per year, dual chamber controlled air incinerators are the recommended configuration. These systems are capable of incinerating a wide range of wastes and, when properly maintained and operated, will achieve emissions of PCDD/F and mercury below the level of the Canada wide Standards. These systems should be equipped with a large secondary chamber sized to provide a residence time of at least one second at a temperature higher than 1000C, to ensure complete combustion and minimize PCDD/F emissions.For facilities incinerating less than 26 tonnes of waste per year, “determined efforts” as defined in the Canada wide Standards for dioxins and furansFootnote should be undertaken. Should circumstances restrict the ability to use a dual chamber incinerator with a large secondary chamber, a single chamber incinerator with an afterburner should be used. It should be noted that such systems are less likely to be able to meet the emission standards than dual chamber incinerators. Both combustion air and dilution air for the barometric damper are required. The intent is to be able to summarize operating parameters during start up, operation asics running and cool down for every cycle. If the required operating conditions are not achieved these data will allow the operators, the manufacturers and the regulator to identify the contributing factors for the failure. From this information, operating procedures can be adjusted to improve performance. Provisions should be made for the manufacturers to be able to remotely access and review the operating data for trouble shooting purposes.It is highly recommended that batch incinerators not be equipped with heat recovery devices. The temperature of the stack gases in heat recovery systems will be lower than in systems without heat recovery, and may be in a temperature range that can lead to the formation of greater quantities of PCDD/F. Similarly, air pollution control systems are not recommended for batch waste incineration systems to control PCDD/F emissions. Stack gases should be released directly to the atmosphere at temperatures higher than 700C to reduce the chances of the inadvertent formation of PCDD/F through the de novo synthesis process.If it is necessary to introduce additional waste to the incinerator during the burn cycle, the incinerator should be equipped with a ram charge system to limit the disruption of combustion in the primary chamber during the waste charging process. food waste); mixed wastes with average energy values; and other materials with high energy values, such as oily waste materials. To facilitate this separation, all waste should be collected in transparent bags. To further assist with separation, wastes could be collected in coloured coded bags. calorific) values. The operator should select waste from each category and mix it to achieve the manufacturer’s specified input calorific value. Each bag should be weighed, its source should be noted, and the total weight of each category should be tallied before completing the loading. This information should be recorded by the computerized data acquisition equipment installed with the incinerator. (Refer to step 6 for further record keeping requirements).Batch incinerator systems have limited charging capacity (both in terms of waste quantity and the calorific value of the wast asics running e charge). To assist the operator with the charging task, particularly for smaller incinerators, several batches could be weighed and placed in their own containers prior to loading the incinerator. The same weighing and logging procedures should be used for each batch and, once recorded, the batch can be charged when appropriate.When the incinerator is charged with the appropriate mix and quantity of waste, the operator should close the door, ensure all interlocks are engaged, and start the burn cycle. The operator should observe the burn for at least 15 minutes after ignition of the primary chamber burner to ensure the volatility of the waste charged is not creating too much gas for the secondary chamber to handle. The rate of combustion can be slowed by reducing the quantity of under fired air. The primary chamber should be operated in the temperature range specified by the manufacturer (typically 500C to 800C).When satisfied that the burn is proceeding in a controlled manner, the operator may leave the incinerator area while the equipment completes the burn cycle.The burn cycle should not be interrupted by opening the charging door until after the burn is complete and the unit has cooled down. No additional waste should be added to the primary chamber unless the incinerator is equipped with an appropriate ram feed device.When the burn is complete and the unit has cooled, the operator should open the door only when wearing protective equipment such as gloves, dust mask, face shield and goggles.The operator should remove the ash from the previous burn cycle before reloading the incinerator. Any unburned materials found in the ash should be recharged to the primary chamber after the operator has cleaned the air ports, and before putting a fresh charge into the incinerator.Training ConsiderationsOperators shoul asics running d be properly trained by the incinerator manufacturer.Top of PageStep 5: Safely Handle and Dispose of Incinerator ResiduesAsh from the primary chamber of the incinerator can contain materials deleterious to the operator’s health and the environment. Operators should use personal protective equipment when handling this material. The material should be carefully rem asics running oved from the hearth and placed in covered metal containers suitable for transporting the ash to an approved disposal site. The operator should weigh, and maintain records of, the quantity of ash produced.